Jump to content

Anyone know if there's a way to test your batteries charge, 4 pin XLR for Eclair ACL


jack layfield

Recommended Posts

I have 4 pin XLR batteries for my Eclair ACL and before I use it I always put the batteries on charge but have no indicator of a full charge or how much is left when shooting. I was wondering if there was a way to plug the batteries in to something or take a reading from them which would let me know how much juice is left on them.

 

 

Link to comment
Share on other sites

  • Premium Member

you could purchase a Chinese voltage meter module (prices starting from 2 bucks I think) and solder it to a 4-pin xlr connector also available cheaply. then you would have a xlr voltage meter which you can just connect to the batteries to see how much voltage they have.

https://www.ebay.com/sch/i.html?_from=R40&_nkw=led+voltage+meter&_sacat=0&_sop=15

Edited by aapo lettinen
Link to comment
Share on other sites

  • Premium Member

The problem is that just reading voltage is unlikely to give a very reliable indication under most circumstances, and for any chemistry other than lithium ion it may be close to useless. Battery fuel gauging is a complex subject, sadly.

Link to comment
Share on other sites

17 hours ago, Gregg MacPherson said:

Do you have a basic multimeter to measure V? Pins 1 and 4 on the canon end of the cable. Can't remember which pins on the jaeger socket on the battery, but trial and error to find out was safe on those batteries.

I do not will get one if this helps?

 

Link to comment
Share on other sites

17 hours ago, Phil Rhodes said:

The problem is that just reading voltage is unlikely to give a very reliable indication under most circumstances, and for any chemistry other than lithium ion it may be close to useless. Battery fuel gauging is a complex subject, sadly.

i don't know the chemistry i'm afraid, i believe the batteries are 12V NiCd or NiMH if that helps? Was just hoping there was a way to take a reading so not always charging and shooting without knowing. 

Link to comment
Share on other sites

  • Premium Member

Aside from just using a multi-meter and putting the probes in the battery socket, there's this sort of thing:

https://www.customcine.store/shop/p/battplug12

But as Phil said, reading the battery voltage when not under load can give you an optimistic reading. Usually if the voltage reads close to the nominal voltage (ie if it reads say 12.3V and it's a 12V battery) then it's close to depleted. A charged 12V battery should read over 13V. But different chemistries can behave differently. Still, a little voltage reader like this is better than nothing and will give you some idea.

Ideally you want to wire a voltage meter in the battery pack itself (which isn't hard, just wire it in parallel) so that you can read the voltage under load. Or make up another power cable with a voltage meter wired in-line, or buy this sort of thing:

https://rencherindustries.com/products/inline-voltmeter?variant=32508861055079

 

Link to comment
Share on other sites

14 hours ago, Dom Jaeger said:

Aside from just using a multi-meter and putting the probes in the battery socket, there's this sort of thing:

https://www.customcine.store/shop/p/battplug12

But as Phil said, reading the battery voltage when not under load can give you an optimistic reading. Usually if the voltage reads close to the nominal voltage (ie if it reads say 12.3V and it's a 12V battery) then it's close to depleted. A charged 12V battery should read over 13V. But different chemistries can behave differently. Still, a little voltage reader like this is better than nothing and will give you some idea.

Ideally you want to wire a voltage meter in the battery pack itself (which isn't hard, just wire it in parallel) so that you can read the voltage under load. Or make up another power cable with a voltage meter wired in-line, or buy this sort of thing:

https://rencherindustries.com/products/inline-voltmeter?variant=32508861055079

 

Hey Dom, thanks for this really helpful and appreciate sending over the link too : )

Link to comment
Share on other sites

You used to be able to buy a battery checker with a 4 pin XLR. This put the battery under some load when you pressed a button and gave the voltage. A battery on the way out gave a voltage that crashed when the button was pressed, if in need of recharge it had amber and red LEDs.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...