Julien Fallecker

Thank you

Hello Someone is selling me an Angenieux 12-120mm Beaulieu r16 autozooming lens. Do you think it will work both manually and automatically (for aperture) on my Beaulieu r16 automatic? thank you

Thank you ! It’s what’s I did

Hello! I have a Beaulieu R16 with a re-celled battery, an old original charger and a Tenergy smart charger. Do you think I can cut the smart charger wire and add the din plug of the old charger to it to be able to charge the battery? otherwise is it possible with the old charger only to charge the new battery re-celled ? thank you

excuse me my level of English does not allow me to answer you but thank you! saw your opinion dispute I will send him my camera and it will make a complete check up. I tested and indeed it is in wide angle that the image is soft. I would have liked for all the qualities of this jewel! but I do not forget that after so many years and format I can not make 16mm! but I love the super 8 and my Nizo also has a problem of sharpness. thanx everybody for your help

Hello do you if collimation is obligatory or a extern filter could be use ? Thanx

thanx!

In a participative lab with a spire but no lomo tank . Why ?

in the lab where I am we devellope with C4 and indeed I look we can develloper negatives too

I knew that the UN 54 could be developed in both ways but you are sure that I can do the same with the N74, I have not found anything on Orwo or on the internet. According to you if I develop it in invertible how many ASA should I use it?

thank you but this recipe is for the reversal film UN54 while I asked for the N74 which is a negative film. but I keep it because I have some too.

do you think the d76 is a good idea or should I use something else?

Thank you ! Merci

hello, I would like to have your advice to develop the N74 400 asa in super 8 not with the D96 but rather the d76 or other photo developer ... thank you !

What amazes me is that I read on forums that it was going to be read at 250 ASA. To know I looked at the aperture with the vacuum camera and with the 500t cartridge and I have the same result (with the filter removed) is this a good way to know?

Hi I have a canon 814 autozoom electronic and i would like to know if my camera will read a vision3, 500t as 400 asa or 250 asa ? Thank you

I have another question, if I use a filter Wratten 85 or 80, I have to change the asa of the camera or just leave like that since there is a loss of aperture of the measurement TTL

For my first short film I filmed with a Yashica which opened to f1,2 like my Bauer and it was of the 200t ... Indeed I should test numerical first to give me an idea but my Olympus omd em5 only opens f3.5 so I could hardly compare.

Hello I have a question about my camera and the indoor shooting with a film kahl NC 21. So 100 ASA. I took it to be able to film inside and outside ... The worry is that I noticed that my camera displays a very open diaphragm compared to a hand cell (basically instead of the theoretical 1/30 camera I have to read 1/125 on the cell) so I need a lot of light to get out of the sub-exposure area of ​​the camera. I do not know if I make myself understood but I wanted to know if I really have to enormously illuminate or if I did not make the diaph of the camera and the result will be correct with a normal light for 1/30. And also in passing if you can give me your opinion on this film.

I thank you I will listen to your advice and I have a friend who used the same film and advised me to expose it to 25 ASA.

Hi and still sorry for the translation ... I bought a film Plus X 16 mm dated 40 years (50 asa) and I wanted to know how much of asa should I expose it. If you can give me your opinion. Thank you...

yes i know it, but i'm lost with the corrections with the 200t and triX i found my results with this document

Hello everyone I have recently owned a Nizo 4056 (so even series that 2056-3056-4080 ...) I try once and for all to interpret results for different dandruff. I will expose them and if you could guide me ... Indeed I am a little lost (and French that translates everything) The probe of the 6-pin camera reads in this order: 40, 40/64, 64/100, 100/160, 160/250, 250/400, 400/640. I can also add photos ;-) So here is what I found: Kodak Tri-x: read 250 ASA tungsten position (thus underexposed by 1/3?) Kodak 50D: read 64 ASA tungsten position (so under expose 1/3?) Kodak 500t: 400 ASA tungsten (so on display? Do nothing?) And for the Kodak 200T (vision 3) I'm less sure ... It is read 160 in tungsten so to change in daylight I do not know (correction of +1/3?) Wittner Chrome (I modified the notch to make it read like 160 otherwise it is read 250 ASA) So if you know this type of camera and have results with these dandruff or other I'm taker! thank you in advance and sorry for my english

Hi I have a Nizo under the eyes with an oxidized battery (batteries) it is a 3046 and I wonder if I can see its operation with only the power cable because only a diode of the filter in the eyepiece lights up . No diode on the outside and no camera action. Maybe you have to go through the batteries? Thank you

Hi all I am new here .... So thank you in advance for your help. I have a Beaulieu 5008 which works to close (even the batteries) but I would like to modify 2 or 3 things on it are screws and the optics has of the play at the level of the camera. I saw a repair manual existed and I wanted to know if someone who has it could give it to me. Thank you (Google translation ;-()