Jump to content
Sign in to follow this  
Montica Pes

Should I push 500T 7229 and 7219?

Recommended Posts

Hello and thank you for any help in advance.

 

I shot my first couple of rolls of 16mm yesterday (Vision 2 and Vision 3 500T in a 16mm Arri from the 60s). To help you understand where I'm coming from with this question, I shoot digital regularly and also 35mm film stills, which I develop. Also, all the tools I was working with yesterday are ancient--finicky in the working, but working.

 

My hope for the two different shorts are medium to high contrast with fine grain and lots of saturation. Here's my problem: I need to know whether to tell Fotokem to push the film a stop or two. Both shorts should take place in a darkened apartment with one practical light suggested as the only light source and a moment where I shoot a darkened room with "moonlight" spilling in--a 250 Lowell light with CTB through a set of blinds. As we were getting readings from an ancient Spectra light meter, the reading kept coming up with a 2.0 on the key side and a 1.0 on the dark of my subjects. The camera's lenses would only open up to a 2f. I was told to overexpose by a stop, but I kept taking a reflected reading using my Canon 7D and getting the light that I wanted--same reading but the light looked right. I exposed for the 2.0f through the entire shoot, not overexposing at all. Also, that means the darks are gonna be DARK.

 

But I'm concerned at this point. Plus, I may not be understanding a "dense" negative. In still film processing, you can only expose the negative once. If I didn't expose for details in the darks, then there really isn't an amount of pushing I can do in the developing that is gonna make up for that after I develop my negative.

 

Should I have exposed for the darks, which would have made the scene look like a well lit daytime scene and then pulled back? (These are shots I took with my 7D with the same settings dialed into what I was dialing into the Arriflex.

 

The performances were so good yesterday, I really want this to turn out and I have to give instructions to the lab tomorrow. Any help is much appreciated.

 

Thank you in advance!

 

Best,

Monty

post-60150-0-34756000-1361502097_thumb.jpg

Share this post


Link to post
Share on other sites

So ur saying the shoot below taken on the 7d were exactly the same settings as the arriflex? If so then your okay vision 3 has 14 stops of dynamic range meaning you could dig deeper into the darks then you could on your 7d and still preserve details.

 

Are you making a print or scan.

Share this post


Link to post
Share on other sites

Thank you Paul for responding.

 

It will be a scan. And yes, the picture was taken on the 7D and the setting were dialed in exactly as to what I put on the Arriflex. So you are saying I should push (overexpose) 1 stop? 2, maybe? :)

Share this post


Link to post
Share on other sites

I think he's saying you'll have more to work in post with than in the digital world without pushing on the developing side.

 

I wouldn't push, if the film matches your still you'll be fine and will not add any extra grain to your final product.

 

Let us know what happens

Share this post


Link to post
Share on other sites

I would not push it either, I think you will be surprised how much shadow detail the stock retains, also a push is more like a gamma change than an overall lift and you might not like the grain in a push +2 with '29 stock. There will be allot of room to bring out the shadow detail in a scan especially with a 2K data scan.

 

-Rob-

Share this post


Link to post
Share on other sites

No need to push go with a 2k scan and advise the colorist how you want the scene to look any notes from the shoot will assist such as camera reports. It's not always about the light it can be about subtracting the light to add drama and contrast.

Share this post


Link to post
Share on other sites

Another route would be to use more light and have the colorist match your 7D sample. In other words, keep the ratio of lighting between the different lights the same, just increase the amount. Then in transfer say you want it to look like "this" and provide your 7D photo. That way you'll have less grain in 16mm and more sharpness.

 

Colorists tell me all the time that it is easy to remove light in post, difficult to add light.

Share this post


Link to post
Share on other sites

You'll be absolutely fine :)

 

Remember, like Rob said, pushing film does far less to effect the shadow detail you "increase" and does much more to the overall contrast and grain. Push if you want high contrast and extra grain, not to actually increase the level of exposure you give the neg. If you underexposed anything less than 2 stops, I think you'll be blown away by how much shadow detail you still have to play with in the telecine/scan, and if you exposed normally (as your 7D indicated) you'll be absolutely great!

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  


  • G-Force Grips



    New Pro Video - New and Used Equipment



    Visual Products



    Ritter Battery



    Media Blackout - Custom Cables and AKS



    Metropolis Post



    FJS International



    Tai Audio



    Rig Wheels Passport



    Wooden Camera



    Glidecam



    Gamma Ray Digital Inc



    Abel Cine



    Serious Gear



    Paralinx LLC



    Broadcast Solutions Inc



    Just Cinema Gear



    CineLab


×
×
  • Create New...