Guest Ronney Ross Posted March 25, 2006 Share Posted March 25, 2006 I have an lower-end cam. (Sears) this camera allows to manual exposure capabilities but a fixed shutter. I want to order a couple of carts next week, being that I am waiting to check out my test footage first hopefully it will be back by Tuesday. Just wondering if I re-notched to cartridge to hopefully get it to read at 100 asa would I have to underexposed,overexpose, or go with light meter readings, Also wondering will renotching give a look close to the 100d reversal stock. I read up a on this a little but could use much help on this issue. Thanks, Ronney Ross Link to comment Share on other sites More sharing options...
Premium Member John Pytlak RIP Posted March 25, 2006 Premium Member Share Posted March 25, 2006 E64T should be notched as a tungsten film, so the orange correction filter should be in place for daylight exposure. With a manual exposure camera, base your exposure on EI-64 with tungsten light and no filter, or EI-40 outdoors with the orange filter in place. Link to comment Share on other sites More sharing options...
KKB22 Posted March 25, 2006 Share Posted March 25, 2006 E64T should be notched as a tungsten film, so the orange correction filter should be in place for daylight exposure. With a manual exposure camera, base your exposure on EI-64 with tungsten light and no filter, or EI-40 outdoors with the orange filter in place. I recently shot a cartridge of the 64T with an old manaul Sankyo camera. The 85 filter did not fit into place like it should have. Is there a trigger in the camera or on the cartridge that I can over ride to make the filter come into position? There is a screw hole on the top of the camera that you trigger to remove the filter for tungsten lighting but that isn't what I am after for exteriors. Link to comment Share on other sites More sharing options...
Maulubekotofa Posted March 25, 2006 Share Posted March 25, 2006 the sears camera may not read anthything other than 160 ro 40 asa so renoching may not be of any use Link to comment Share on other sites More sharing options...
Premium Member John Pytlak RIP Posted March 25, 2006 Premium Member Share Posted March 25, 2006 the sears camera may not read anthything other than 160 ro 40 asa so renoching may not be of any use They said it had manual exposure capabilities. If so, they just need to be sure the orange filter (internal or external) is in place for daylight exposure, meter the light, and set the exposure manually. Link to comment Share on other sites More sharing options...
S8 Booster Posted March 25, 2006 Share Posted March 25, 2006 I recently shot a cartridge of the 64T with an old manaul Sankyo camera. The 85 filter did not fit into place like it should have. Is there a trigger in the camera or on the cartridge that I can over ride to make the filter come into position? There is a screw hole on the top of the camera that you trigger to remove the filter for tungsten lighting but that isn't what I am after for exteriors. you may try to verify the built in 85 filter control vs cart notching as seen below. this info is for the 200t cart - how to allow use of the built in 85 filter as the 200t cart is incorrectly notched from kodak. the principle for 85 filter control is the same for any cart if your camera is fully compliant to to the standard. here is what you need to do to make the cam read the cart as 160/100: this is where the filter notch is located - open it and the cam is allowed to read it as either 160 for tungetsen (when the built in 85 filter is disabled) or 100 with the filter in place for daylight shoot. Click images for biger size: how to mod and why: s8hôôt s8hôôt Link to comment Share on other sites More sharing options...
Maulubekotofa Posted March 25, 2006 Share Posted March 25, 2006 if your sears camera is a low light XL model then it is best to assume a 220 detgrees shiuttter. if it is not a low light xl camera, then base your light meter settings on a 160 degrees shutter. anotherwords if you are using a still camera light meter you have to account for the internal shutter speed of your camera. this is typically 1/40th of second for a regular camera or 1/30th of a second for a xl camera this is the shutter speed to use to get the right f-stoip Link to comment Share on other sites More sharing options...
Anthony Schilling Posted March 25, 2006 Share Posted March 25, 2006 (edited) Keep it simple. if your cam reads 40/160 only and your meter is reading f5.6, use manual adjustment and set -1/3 from f8. in other words, set your exposure 2/3rds of the way to the next highest # in your meter. Edited March 25, 2006 by Skratch Link to comment Share on other sites More sharing options...
KKB22 Posted March 26, 2006 Share Posted March 26, 2006 you may try to verify the built in 85 filter control vs cart notching as seen below. this info is for the 200t cart - how to allow use of the built in 85 filter as the 200t cart is incorrectly notched from kodak. the principle for 85 filter control is the same for any cart if your camera is fully compliant to to the standard. s8hôôt Thanks man!! :D Link to comment Share on other sites More sharing options...
Guest Ronney Ross Posted March 27, 2006 Share Posted March 27, 2006 Thanks all for the wealth of info. -Ronney Ross Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now