Search the Community
Showing results for tags 'krasnogsk-3'.
Hi there, I purchased a K3 in March 2021 from a highly rated seller on eBay and shot 5 reels since then. The camera came in great condition and the first 3 reels came back perfectly fine, no light leaks and no scratches. Most of the footage from the 4th reel came back shaky and split, (as you can see on the video below), however some of the last shots on that reel came out fine and stable. I thought it was a matter of me not loading the film properly or the pressure plate not sitting tightly in the camera. I shot the final reel a couple weeks ago and it came back with the same issue, but on the entirety of the footage this time. I am based in London and sent my K3 to a repair shop. They sent me a quote of 708£ (which exceeds my budget) for a full clean and repair, along with this message « The main faults that need repairs are the claw and transport system. Scratching and auto loading cannot be improved if occurs - common fault with this model » . Now I still have the loop formers on my K3 and having done some research, I found that some people had similar issues and that removing the loop formers could solve them.The camera was in perfect working condition and I take great care of it : I checked it before sending it for repairs and found no damage whatsoever. I know that the loop formers operate on a thread mechanism and therefore might not be very reliable. Then again, I'm new to this so looking for any advice! Thanks https://kapwi.ng/c/NpXtAiQXqr https://we.tl/t-bVLvVtNxV3
Hi Guys, I own a Krasnogorsk K-3, I purely use it for fun, not professionally. I've put about three rolls through it at this stage, and although I'm happy with the quality of the footage, I notice a large dust build up on all the the footage, as well as some continuous straight scratching on the right side of the film. Have been quoted £400 to have the camera professionally cleaned and serviced, but it's not worth that so I'm not really willing to fork out that much just for a camera that I use for fun. Was wondering if anyone here has experience of cleaning this camera themselves? And if they could give any advice to potentially fixing this at home? I gave the camera a good blow with compressed air, and a little brush the last time I put a roll through it, but still got the recurring issues. Any other help would be massively appreciated! I have attached some images for reference. Best, Jack
Hello group, Solving the (hopefully) last problems with my S 16 K-3. Looking good so far. No emulsion scratches (after a lot of very careful polishing the gate in the right areas - loop formers removed) and just found the cause for the occasional base/backing scratch (exactly where the regular 16mm frame would end opposite pulldown claw. It's caused by the plastic part that leads the film out of (top) and back into (bottom) the sprocket/roller assembly. The part has sharp edges/burrs on both sides: top and bottom side. Too difficult to remove the part, so I'll tape off the rollers and some light wet (always fine machine oil, not water) sanding with 1000 and 2000 grade should solve the base/backing scratches once and forever. Now those nasty orange-red light leaks (sprocket hole side). I see these - looking exactly the same - on a lot of K-3 footage on YouTube and Vimeo. I went through the footage frame by frame ( "," and "." keys on YouTube). These occur roughly along 3-4 frames (with some light spill) 26 to 30 frames before and less frames after a new shot (the white flash frame). Checked with scrap film: this locates the leakage exactly at the back side of the spools - and the emulsion is inside black "daylight" spools (???) Can't come from the footage counter: sealed it off with gaffer tape. It's clearly light that finds its way slowly to these areas when the camera is not running but exposed to bright light. If I don't expose the camera to a lot of light, or only have a short break, between shots: no light leaks there. The fact that the baffle plate is a silver-gray with a dot pattern (as opposed to matte black - the way it should be)) certainly doesn't help matters. Door and lock are always sealed tight with black camera tape. This seems to remain a mystery for many a K-3 user. Painting any parts inside matte black is out of the question (I think): it can chip and probably cause chemical reactions. Any ideas and tips highly appreciated. Thanks in advance, Christian