Search the Community
Showing results for tags 'cartridges'.
Found 2 results
Hello folks, I'm new on cinematography.com, i'm getting into super-8 as a member of an analog associative Photo/Cinema called ZebraLab based in Geneva : https://zebralab.info/. I am also a photographer by job. With the guys from the lab, we are/have built two machines to cut reels of Fomapan R100 DS8x30,5M to 4x S8x15M to be loaded in Lomo Reloadable Cartridge. That make it really affordable as we buy from Foma factory shop, we are around 7€ for the film and around 3€/film for processing (detail below). According to Super8Wiki, Lomo Reloadable Cartridge acts as 64T/40D -> http://super8wiki.com/index.php/Super_8_Cartridge_Notch_Ruler (down of the page). We would like to turn them into ASA 100, but we don't know wich notch ruler we should trust : - The one from Super8Wiki : super8wiki.com/images/6/6f/Cartridgenotchruler.pdf - Or that one who says the Super8Wiki notch ruler is not that good : http://www.peaceman.de/schmalfilm/super8/S8_Notch_Tools_v1.0.pdf We asume that : as the Fomapan R100 is black and white and that the contrast change induced by the CCA filter is not that big of a deal for us whe should turn the ASA 40D to an ASA 100T, thus cuting a filter notch down on the cartridge and enlarging the upper notch, correct ? Also, as several of us own (and ZebraLab also) a Canon 814 XL-S in working condition, we would like to give a shot at turning one of the cartridge to ASA 400, as the film stock can be pushed 2 stop during processing : we are processing black and white reversal with a mix of two method : Potassium Permanganate + Sulfuric Acid bleach and using a photopaper developper, as the emultion if soften by the bleach, we do hardening bath before to the bleach and one hardening fix bath after second developpement. The hardening concentrate is the Tetenal one (Aluminium Sulfite + Acetic Acid but that need confirmation). You can watch the result here on a Kodak Tri-X 200. (i found the result to be a bit too much contrasted...) But, according to the Super8Wiki notch ruler we are not sure that the Canon 814 XL-S can read ASA 400, even if it say so on different website (that would mean not a notch is pushed by the cartridge, 6 notches without the filter notch, and we tried cuting into an old K40 to make it ac as a ASA 400T but it doesn't seem to make a difference for the exposure sensor, that same camera read and exposed correctly the Kodak Tri-X 200 that you can watch on vimeo...). So : is it possible to turn a cartridge to ASA 400T (or around like a 500T), and would a Canon 814XL-S be able to read it, it can read Vision3 500T, so i guess yes, but how ? That's it for the moment, if you have solutions and/or questions, i'm up for it ! Bye, Jeremy
Hi, I recently bought some bulk super 8 film from Wittner and a reloadable super-8 cartridge. And when practicing loading with dead film, I'm struggling to get the super-8 to run smoothly through my camera, as Wittner cartridges does not come with the copper ring used to keep the film in place. I think they have replaced the copper ring with a clear plastic larger ring (seen in the photo, inside the cartridge on the right) that is suposed to keep the film (on the receiving side of the cartridge) in place some how? Here is a photo of everything supplied with the cartridge: Please could someone give me some advice on how to load these cartridges? I have seen some information on this forum about DIY reloadable cartridges but not the Wittner cartridges. I hope this makes sense, Thanks in advance. -Harry