Nooman Naqvi Posted August 15, 2006 Share Posted August 15, 2006 Is there a place or a gentlemen in Chicago to whom I can pay and learn basic operations (familiarize myself) on the Arri 2C? Link to comment Share on other sites More sharing options...
Daniel Stigler Posted August 15, 2006 Share Posted August 15, 2006 The IIC is a very simple camera. A while ago the manual was posted here. If you have some basic understanding for motion picture cameras you will be fine after reading the manual. Be sure to use batteries with the correct voltage (16V) as this is the most common source of problems when shooting with a IIC. Link to comment Share on other sites More sharing options...
Premium Member Hal Smith Posted August 15, 2006 Premium Member Share Posted August 15, 2006 Is there a place or a gentlemen in Chicago to whom I can pay and learn basic operations (familiarize myself) on the Arri 2C? You might try asking around if there's an experienced 1st AC who can run you through basic 2C operation. I figured mine out by myself because I live in the backwaters here in OK but there's got to be a least a few old hand AC's in Chicago with hands-on 2C experience. If you strike out, you might ask on the AC Forum here if there's an AC in the city who can help you. One thing I did do with mine was get a roll of junk film and practice loading mags and threading the camera until I was blue in the face (and red in the fingers). It would be worth the money to buy a short end of film to have something to practice with, older emulsion short ends and recans can go pretty cheap on eBay. Link to comment Share on other sites More sharing options...
Premium Member Dan Goulder Posted August 15, 2006 Premium Member Share Posted August 15, 2006 Is there a place or a gentlemen in Chicago to whom I can pay and learn basic operations (familiarize myself) on the Arri 2C? A 2C is pretty cheap to rent. There are a number of rental houses in Chicago(SMS, Fletcher, etc.). If you rent one for a day or two, the folks at the rental house can show you how to load the camera and run it. Link to comment Share on other sites More sharing options...
Nooman Naqvi Posted August 16, 2006 Author Share Posted August 16, 2006 Thanks guys. Hal thats a good suggestion. I'll post on the forum for that. Link to comment Share on other sites More sharing options...
Nooman Naqvi Posted August 17, 2006 Author Share Posted August 17, 2006 Hal, I went to ebay for Arri 2C 400ft magazine, didnt find any there. Can you point me to a cheap place to buy one? Link to comment Share on other sites More sharing options...
Premium Member Hal Smith Posted August 19, 2006 Premium Member Share Posted August 19, 2006 Hal, I went to ebay for Arri 2C 400ft magazine, didnt find any there. Can you point me to a cheap place to buy one?They show up on eBay on a fairly regular basis - keep looking, do searches in "All Categories" for "Arri" and "Arriflex" both. It might be worth a call to Visual Products, they can be a bit high on prices but back everything they sell 100%, I've got personal experience of their willingness to make sure the buyer is happy. An afterthought: Threading the magazines goes a lot easier if you cut the film off square and exactly between sprocket holes. I don't have one but I believe Arri actually makes a gauge you can use in a changing bag to assist in trimming the new roll of film at exactly the correct place. Does anyone out there know what Arri calls them and what they cost? Link to comment Share on other sites More sharing options...
Daniel Stigler Posted August 19, 2006 Share Posted August 19, 2006 An afterthought: Threading the magazines goes a lot easier if you cut the film off square and exactly between sprocket holes. I don't have one but I believe Arri actually makes a gauge you can use in a changing bag to assist in trimming the new roll of film at exactly the correct place. Does anyone out there know what Arri calls them and what they cost? These things are called ARRI Film Cutting Gauge. I never used one but they sure are a helpful tools for starters. 99% of the Kodak rolls i ever loaded were cut through the holes but it's a different story with Fuji. Nooman: Filmstock can easily be torn apart by hand at the sprocket hole. With a little experience you can do this in the changing bag to get the end to thread easier. You can practice that with a shortend and see if it works out for you. If doing this when loading be sure not to get any filmchips into the magazine. Link to comment Share on other sites More sharing options...
Chris_Burket Posted September 22, 2006 Share Posted September 22, 2006 Most rental houses will be happy to let you learn how to load mags and operate a camera, as long as its in house of course. Just go into a rental house, introduce yourself, and ask. I would avoid Monday and Friday though, these can be busy days. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now