Search the Community
Showing results for tags '814 xl-s'.
Found 4 results
Hello folks, I'm new on cinematography.com, i'm getting into super-8 as a member of an analog associative Photo/Cinema called ZebraLab based in Geneva : https://zebralab.info/. I am also a photographer by job. With the guys from the lab, we are/have built two machines to cut reels of Fomapan R100 DS8x30,5M to 4x S8x15M to be loaded in Lomo Reloadable Cartridge. That make it really affordable as we buy from Foma factory shop, we are around 7€ for the film and around 3€/film for processing (detail below). According to Super8Wiki, Lomo Reloadable Cartridge acts as 64T/40D -> http://super8wiki.com/index.php/Super_8_Cartridge_Notch_Ruler (down of the page). We would like to turn them into ASA 100, but we don't know wich notch ruler we should trust : - The one from Super8Wiki : super8wiki.com/images/6/6f/Cartridgenotchruler.pdf - Or that one who says the Super8Wiki notch ruler is not that good : http://www.peaceman.de/schmalfilm/super8/S8_Notch_Tools_v1.0.pdf We asume that : as the Fomapan R100 is black and white and that the contrast change induced by the CCA filter is not that big of a deal for us whe should turn the ASA 40D to an ASA 100T, thus cuting a filter notch down on the cartridge and enlarging the upper notch, correct ? Also, as several of us own (and ZebraLab also) a Canon 814 XL-S in working condition, we would like to give a shot at turning one of the cartridge to ASA 400, as the film stock can be pushed 2 stop during processing : we are processing black and white reversal with a mix of two method : Potassium Permanganate + Sulfuric Acid bleach and using a photopaper developper, as the emultion if soften by the bleach, we do hardening bath before to the bleach and one hardening fix bath after second developpement. The hardening concentrate is the Tetenal one (Aluminium Sulfite + Acetic Acid but that need confirmation). You can watch the result here on a Kodak Tri-X 200. (i found the result to be a bit too much contrasted...) But, according to the Super8Wiki notch ruler we are not sure that the Canon 814 XL-S can read ASA 400, even if it say so on different website (that would mean not a notch is pushed by the cartridge, 6 notches without the filter notch, and we tried cuting into an old K40 to make it ac as a ASA 400T but it doesn't seem to make a difference for the exposure sensor, that same camera read and exposed correctly the Kodak Tri-X 200 that you can watch on vimeo...). So : is it possible to turn a cartridge to ASA 400T (or around like a 500T), and would a Canon 814XL-S be able to read it, it can read Vision3 500T, so i guess yes, but how ? That's it for the moment, if you have solutions and/or questions, i'm up for it ! Bye, Jeremy
Hello, I recently bought a Canon 814 XL-s that seems to be in mint condition externally. The only visible issue are the seals around the cartridge compartment that are ruined and falling off. But upon trying it out this problem arose: Problem: The film speed dial works erratically. Sometimes the motor will spin slow, sometimes medium, sometimes fast (about 0.5, 1.15 and 1.5 rounds per sec) independently of where the dial is pointing, but changing if I push it around by shifting it or pressing it lightly. The Slow-mo button always works, instead. I still have to try other functionalities such as fades, preset bursts and changing the shutter angle. I'm guessing it's just a problem with the selector's contacts... I've heard these are not so easy to reach, but then perhaps a little contact cleaner might be enough. I've only opened some Nizos, this seems a little more complex, and I found nothing online... Any ideas on how to reach these contacts, or about what else it could be? Thanks!
Really handy piece of kit, in near mint condition. £80 GB Pounds plus shipping. :)
All film tested and fully functioning with crystal clear lenses: Canon 814 XL-S £150 GB Pounds Eumig Nautica £100 GB Pounds Bolex 680 £100 GB Pounds Canon 514 XL-S £60 GB Pounds Payment by PayPal plus actual shipping cost will be added (please ask for quote).