Jump to content
Bill Hilly

Bolex Blues: Did I snap my spring?

Recommended Posts

Hello all,

 

I've got a dour situation on my hands with my new Bolex H16. Not sure which model exactly - it's an eBay find - but it has a variable shutter so I think it's an Rx2.

 

It was running fine this evening as I was putting my first roll through. I wanted to try to do a double exposure and rewound the camera a few feet. Then when I re-engaged the motor I heard an unnatural noise. Suffice to say, that motor isn't running any more.

 

I've removed the film - there didn't seem to be any jams. I've tried single frame and slow-speed continuous running but neither have engaged the motor. The crank is tight, like it has a full wind, but won't move in either direction when engaged. And the rewind works... in both directions.

 

Does this sound like a spring problem? Any other ideas? This is my first Bolex and I might have gotten to antsy to try out its special effects...

 

Share this post


Link to post
Share on other sites

It sounds like the motor is still disengaged - the winding lever won't wind when the motor is disengaged. Try moving the MOT <-> O lever to O again, use the rewind crank to wind forward a few frames (with the run release pressed), then re-engage the motor (with the release in the stop position). The MOT <-> O lever should spring back to the MOT position. Make sure that lever is firmly keyed on to the square pin beneath, if the screw is a bit loose or the mating parts are worn the lever may not be actually turning the pin.

 

If it still won't engage, the gear inside is jammed for some reason. (It's unlikely the spring itself is broken, that would cause a different fault.) You would then need to decide whether to send it to a repairman, try to open it up yourself, or just buy another body.

 

 

Share this post


Link to post
Share on other sites

It is virtually impossible to “snap” the spring of such a camera. I have never heard of a broken spring with a Bolex or any other spring-driven movie camera.

 

Your model appears to be about 54 years old and most probably never serviced, so sticky with oxidized mineral grease. What presumably happened is that the catch ratchet caught by the excentric stop on the 0-MOT axle didn’t turn back when you reengaged the spring (MOT). The gear train then got stalled which is possible under sticky-dry conditions.

 

Disengage the clutch (0), move the mechanism with the hand crank on the axle designated with a rounded counterclock arrow, remove crank, set side switch to STOP, and engage clutch (MOT). A vigorous blow should occur, that’s the spring falling into the gear train with its full load. It is possible that somebody damaged a catch tooth by insensibly forcing the clutch lever. A service job is up anyhow.

 

Before you spend money I’d suggest you deliberate what you need. Perhaps an H-16 is not the best camera for you at the moment. Please do think over whether you want a toy to play with or a camera for obtaining pictures that you want to study or perhaps show to others.

Share this post


Link to post
Share on other sites

I've also replaced many broken spring motors, just a few months ago I had a Bolex with a broken spring come into my workshop.

 

It's by no means unbelievable.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Gamma Ray Digital Inc



    Metropolis Post



    Glidecam



    Just Cinema Gear



    G-Force Grips



    Serious Gear



    Abel Cine



    Tai Audio



    Paralinx LLC



    New Pro Video - New and Used Equipment



    Media Blackout - Custom Cables and AKS



    Visual Products



    CineLab



    Broadcast Solutions Inc



    Wooden Camera



    FJS International



    Ritter Battery



    Rig Wheels Passport


×
×
  • Create New...